🚀 Ryzen 7 7800X3D + RTX 4070 Ti SUPER TUF + FW360 LCD AIO + 32GB DDR5 + PCIe 5.0 PSU + ARGB Mods 🎮 Phil’s Builds — Boutique Validated System | Silent, Polished, Resale-Ready

Built for high-FPS gaming, low noise floor, and resale integrity. Every component validated. No filler. No assumptions.

🧩 Core Specs

🖥️ CPU: AMD Ryzen 7 7800X3D — 8C/16T | 4.2GHz base | 5.0GHz boost | 96MB L3 cache.

🎮 GPU: ASUS TUF RTX 4070 Ti SUPER — 16GB GDDR6X | triple-fan | DLSS 3.5 | PCIe 4.0.( light gaming use, few months old)

❄️ Cooler: Thermalright FW360 AIO — 360mm | 3x PWM ARGB fans | IPS LCD telemetry (320×240).

🛠️ Motherboard: Gigabyte B650 AORUS ELITE AX — AM5 | PCIe 4.0 | Wi-Fi 6 | 2.5Gb LAN.

🧠 RAM: Corsair Vengeance RGB — 32GB (2x16) DDR5-6000 CL36 | ARGB sync validated.

⚡ Storage: KingSpec NX-2280 — 1TB NVMe Gen4 (boot) + KingSpec XG7000 — 2TB NVMe Gen4 (games/storage).

🔌 PSU: Apevia ATX-PR1000W Prestige — 1000W | 80+ Gold | ATX 3.0 / PCIe 5.0 | native 12VHPWR.

🖤 Case: FOIFKIN F1 ATX Mid-Tower — panoramic glass | dual-chamber | Type-C I/O | 6x ARGB fans pre-installed.

🗂️ Storage Configuration Note This system includes two NVMe drives:

1TB KingSpec NX-2280 Gen4 — boot/system drive (validated, thermal pad applied)

2TB KingSpec XG7000 Gen4 — secondary drive for games and storage (validated, zero throttling under load)

⚠️ Jawa’s listing form only allows one M.2 entry and maxes out at 2TB total. Actual combined capacity is 3TB across dual Gen4 NVMe drives.

🧊 Fan Layout & Airflow:

🌀 Total Fans: 10x darkFlash INF34 PWM ARGB — 2000RPM max | plate-to-plate daisy-chain

3x rear chamber (reverse ARGB aesthetic intake)

1x rear exhaust

3x bottom intake

3x front intake (mounted to AIO radiator) 🌬️ Airflow Configuration:

Intake: 6x — bottom + front

Exhaust: 4x — rear + top (AIO push) ✅ No flutter, tonal hum, or wind artifacts detected ✅ ARGB sync validated via 5V 3-pin header — no controller included

🔌 Cable Mods & GPU Power

🧵 AIJS 24PIN PSU Extension Cable — 30cm | 18AWG | 90° right-angle | ARGB via 5V 3-pin 🧲 Bangfun PCIe 5.0 12VHPWR Adapter — 90° right-angle | 16AWG | 400W sustained draw ↪️ Terminal fitment confirmed on TUF 4070 Ti SUPER — no thermal anomalies ↪️ No signal loss or ripple under gaming load

✅Validation & Prep

BIOS tuned for X3D boost behavior

Drivers installed and logged

Cable routing optimized

OOBE scrubbed and buyer-ready

System stress-tested and documented

LCD telemetry validated — no pixel defects.

📸 Additional Media & Validation Incoming More photos, benchmark screenshots, and stress test logs will be uploaded shortly. System has already passed full validation — including a 99.8% score on 3DMark Port Royal, confirming elite ray tracing performance. Telemetry, thermal behavior, and acoustic data will be included for buyer transparency.

📦 Condition: All components confirmed functional and validated. No filler, no assumptions. 💬 Message for alternate GPU, cooler, or RAM options. 🛡️ Phil’s Builds — Trusted boutique PC builder. Every part validated. Every listing transparent.